Ab einen Bestellwert von 240,- € berechnen wir keine Versandkosten innerhalb von Deutschland (außer bei "scharfen" Waffen).
Alle Preise verstehen sich incl. MwSt.
Für Lieferungen außerhalb von Deutschland gelten pauschal Versandkosten von 15,- € (außer für "scharfe" Waffen)

Tuning » Abzug 1 2 32 Artikel

Für den perfekten Glock Abzug (nach unserer Meinung)

Federset - welche maßgeblich das Abzugsgewicht beeinflusst - vom US Tuningsspezialist ZEV GLOCKWORX der noch weitere schöne Teile für die GLOCK Pistolen herstellt - welche wir auch vertreiben...
Das ZEV// Tech Kit besteht aus: Steuerfeder PRO, Schlagbolzenfeder (weich), Abzugsfeder (härter) und Sicherungsfeder (weich) und wird nur gegen die originalen Teile ausgetauscht.

Egal welche Generation Deine GLOCK ist.

Also für Gen. 1, Gen. 2, Gen. 3, Gen. 4 & Gen. 5 (bei Gen.5 braucht man die Abzugsfeder nicht)

Egal welches Modell Du hast...

Also für GLOCK 17, 19, 26, 22 31, 37, 20,21, 23, 25, 32, 38, 27, 28, 33, 39, 29, 30, 36, 34, 24, 35, 40, 41

nein, für die 42 & 43 NICHT!

Angegeben sind 2 IBS Abzugsgewicht (in der Realität kommt 1.700gr. - 1.600gr. raus)

Einbau im Geschäft kostet 5,-EU extra. Kein Termin erforderlich - dauert ca. 5 Minuten...

Glockworx-Federsatz einbauen
Griffstück
- Magazin entfernen
- Verschluss abnehmen
- Hinteren Bolzen am Griffstück rausdrücken
- Kleiner Bolzen über Abzug rausdrücken
- Großer Bolzen vom Abzug raus (Schlittenfang dabei bewegen)
- Schlittenfang rausnehmen
- Steuerblock nach oben raus hebeln
- Abzugssystem komplett nach oben rausnehmen
- Abzug/Abzugsstange schräg nach vorn aushängen
- Abzugsstange von Feder trennen
- Feder aus Abzugsblock entfernen (nicht bei Gen.5)
- Neue Feder einhängen (nicht bei Gen.5)
- Steuerfeder rausdrücken
- Neue Steuerfeder einsetzen
- Abzugsstange in Abzugsfeder einhängen
- Abzugsstange in Steuerblock einsetzen
- Komplettes Abzugssystem in Griffstück setzen
- Hinterer Bolzen einsetzen
- Verrieglungsblock rein
- Kleinen Bolzen einsetzen (wichtig - den zuerst)
- Schlittenfang zwischen Abzug und Gehäuse einsetzen
- Abzugsbolzen einsetzen
Schlitten (Verschluss):
- Federführungsstange und Lauf herausnehmen
- Deckplatte (Coverplate) abnehmen
- ! Vorsicht Feder !
- Schlagbolzen nach hinten rausnehmen
- Feder mit Druckstange raus
- Fallsicherung reindrücken
- Auszieher seitlich raus schütteln
- Fallsicherung entfernen, Feder rausziehen und gegen Neue ersetzen
- Fallsicherung und Feder einsetzen und nach unten drücken
- Auszieher einsetzen und Fallsicherung loslassen
- Druckstange mit Feder einsetzen (Feder schaut nach hinten)
- Schlagbolzen in die Hand nehmen
- Feder zurückziehen
- Federteller entfernen !Vorsicht!
- Feder vom Schlagbolzen ziehen
- Neue Feder einsetzen
- Feder zurückziehen und Teller einsetzen
- Schlagbolzen wieder in Schlitten einsetzen
- Lauf und Federführungsstange einbauen
- Verschluss und Griffstück zusammensetzen
- Fertig
 :  
48,00 € (incl. Mwst. zzgl. Versand)
 

The Cleanest, Most-Crisp Trigger Pull Found on the Market Today
One of the pioneers in the huge market for Glock trigger upgrades was Zev Technologies, a company that found incredible success in competition with its trigger enhancements. To improve the product, though, Zev’s engineers went back to the drawing board and spent thousands of hours designing an improved trigger upgrade. The result was the Zev Technologies Glock Pro Flat Face Trigger Upgrade Kit. Each Zev Glock Pro Flat Face Trigger Upgrade Kit developed through hundreds of thousands of rounds of testing, leading to the design of a proprietary trigger bar and connector that offer the cleanest, most-crisp trigger pull found on the market today. The new trigger pad is built with a riveted assembly that makes it one of the most-durable replacement options available to today’s Glock users. Each Zev Pro Flat Face Trigger Upgrade Kit is compatible with a range of Glock handguns from generations 1 through 5, including the Gen 5 models of the G19, G17, G34, G19X and G45.

“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
 :  
185,00 € (incl. Mwst. zzgl. Versand)
 

Gibt es mit schwarzen oder roten Abzugszüngel!
Ultra-Crisp Trigger, Glass Smooth Break
Bringing a wealth of knowledge and experience from its presence in the aftermarket for AR-15 triggers, CMC Triggers entered the handgun market with a modified trigger unit for one of the world’s most-popular handgun designs: the Glock. Each CMC Glock Replacement Trigger provides owners with a drop-in unit designed to instantaneously enhance the performance of their gun’s trigger. The CMC Triggers Glock Replacement Trigger is a complete unit that features OEM internals, including a Glock OEM trigger bar, springs and housing. However, the design features a flat-faced trigger shoe with a hooked bottom that reduces pull weight by two pounds over the OEM design. The trigger is constructed from a combination of 8620 alloy steel and S7 tool steel and features a positive trigger reset.

“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
 :  
260,00 € (incl. Mwst. zzgl. Versand)
 

Gibt es mit schwarzen oder roten Abzugszüngel!
Ultra-Crisp Trigger, Glass Smooth Break
Bringing a wealth of knowledge and experience from its presence in the aftermarket for AR-15 triggers, CMC Triggers entered the handgun market with a modified trigger unit for one of the world’s most-popular handgun designs: the Glock. Each CMC Glock Replacement Trigger provides owners with a drop-in unit designed to instantaneously enhance the performance of their gun’s trigger. The CMC Triggers Glock Replacement Trigger is a complete unit that features OEM internals, including a Glock OEM trigger bar, springs and housing. However, the design features a flat-faced trigger shoe with a hooked bottom that reduces pull weight by two pounds over the OEM design. The trigger is constructed from a combination of 8620 alloy steel and S7 tool steel and features a positive trigger reset.

“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
 :  
260,00 € (incl. Mwst. zzgl. Versand)
 

Gibt es mit schwarzen oder roten Abzugszüngel!
Ultra-Crisp Trigger, Glass Smooth Break
Bringing a wealth of knowledge and experience from its presence in the aftermarket for AR-15 triggers, CMC Triggers entered the handgun market with a modified trigger unit for one of the world’s most-popular handgun designs: the Glock. Each CMC Glock Replacement Trigger provides owners with a drop-in unit designed to instantaneously enhance the performance of their gun’s trigger. The CMC Triggers Glock Replacement Trigger is a complete unit that features OEM internals, including a Glock OEM trigger bar, springs and housing. However, the design features a flat-faced trigger shoe with a hooked bottom that reduces pull weight by two pounds over the OEM design. The trigger is constructed from a combination of 8620 alloy steel and S7 tool steel and features a positive trigger reset.

“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
 :  
260,00 € (incl. Mwst. zzgl. Versand)
 

Gibt es mit schwarzen oder roten Abzugszüngel!
Ultra-Crisp Trigger, Glass Smooth Break
Bringing a wealth of knowledge and experience from its presence in the aftermarket for AR-15 triggers, CMC Triggers entered the handgun market with a modified trigger unit for one of the world’s most-popular handgun designs: the Glock. Each CMC Glock Replacement Trigger provides owners with a drop-in unit designed to instantaneously enhance the performance of their gun’s trigger. The CMC Triggers Glock Replacement Trigger is a complete unit that features OEM internals, including a Glock OEM trigger bar, springs and housing. However, the design features a flat-faced trigger shoe with a hooked bottom that reduces pull weight by two pounds over the OEM design. The trigger is constructed from a combination of 8620 alloy steel and S7 tool steel and features a positive trigger reset.

“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
 :  
260,00 € (incl. Mwst. zzgl. Versand)
 

Gibt es mit schwarzen oder roten Abzugszüngel!
Ultra-Crisp Trigger, Glass Smooth Break
Bringing a wealth of knowledge and experience from its presence in the aftermarket for AR-15 triggers, CMC Triggers entered the handgun market with a modified trigger unit for one of the world’s most-popular handgun designs: the Glock. Each CMC Glock Replacement Trigger provides owners with a drop-in unit designed to instantaneously enhance the performance of their gun’s trigger. The CMC Triggers Glock Replacement Trigger is a complete unit that features OEM internals, including a Glock OEM trigger bar, springs and housing. However, the design features a flat-faced trigger shoe with a hooked bottom that reduces pull weight by two pounds over the OEM design. The trigger is constructed from a combination of 8620 alloy steel and S7 tool steel and features a positive trigger reset.

“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
 :  
260,00 € (incl. Mwst. zzgl. Versand)
 

Gibt es mit schwarzen oder roten Abzugszüngel!
Ultra-Crisp Trigger, Glass Smooth Break
Bringing a wealth of knowledge and experience from its presence in the aftermarket for AR-15 triggers, CMC Triggers entered the handgun market with a modified trigger unit for one of the world’s most-popular handgun designs: the Glock. Each CMC Glock Replacement Trigger provides owners with a drop-in unit designed to instantaneously enhance the performance of their gun’s trigger. The CMC Triggers Glock Replacement Trigger is a complete unit that features OEM internals, including a Glock OEM trigger bar, springs and housing. However, the design features a flat-faced trigger shoe with a hooked bottom that reduces pull weight by two pounds over the OEM design. The trigger is constructed from a combination of 8620 alloy steel and S7 tool steel and features a positive trigger reset.

“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
 :  
260,00 € (incl. Mwst. zzgl. Versand)
 

Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel; Drop-In Installation
Convenient kits combine easy drop-in installation with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Complete Trigger Kit contains the trigger, trigger bar, trigger block, ejector, connector, trigger spring, and a lightweight stainless steel firing pin safety plunger and spring to further refine the trigger pull. Comes with a reduced-power striker spring to produce a lighter-feeling trigger for competition, and the factory-weight striker spring for daily carry and duty use.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
SPECS: .45 DROP IN AND ULTIMATE ONLY FIT .45 ACP. IN GEN-1 THRU GEN-3 GUNS. 10mm uses a different firing pin safety diameter that can’t be used on a .45 nor can the .45 be used on the 10mm.
Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
Bis Gen 3
 :  
310,00 € (incl. Mwst. zzgl. Versand)
 

Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel; Drop-In Installation
Convenient kits combine easy drop-in installation with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Complete Trigger Kit contains the trigger, trigger bar, trigger block, ejector, connector, trigger spring, and a lightweight stainless steel firing pin safety plunger and spring to further refine the trigger pull. Comes with a reduced-power striker spring to produce a lighter-feeling trigger for competition, and the factory-weight striker spring for daily carry and duty use.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
SPECS: .45 DROP IN AND ULTIMATE ONLY FIT .45 ACP. IN GEN-1 THRU GEN-3 GUNS. 10mm uses a different firing pin safety diameter that can’t be used on a .45 nor can the .45 be used on the 10mm.
Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
Bis Gen 3
 :  
310,00 € (incl. Mwst. zzgl. Versand)
 

Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel; Drop-In Installation
Convenient kits combine easy drop-in installation with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Complete Trigger Kit contains the trigger, trigger bar, trigger block, ejector, connector, trigger spring, and a lightweight stainless steel firing pin safety plunger and spring to further refine the trigger pull. Comes with a reduced-power striker spring to produce a lighter-feeling trigger for competition, and the factory-weight striker spring for daily carry and duty use.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
SPECS: .45 DROP IN AND ULTIMATE ONLY FIT .45 ACP. IN GEN-1 THRU GEN-3 GUNS. 10mm uses a different firing pin safety diameter that can’t be used on a .45 nor can the .45 be used on the 10mm.
Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
Bis Gen 3
 :  
310,00 € (incl. Mwst. zzgl. Versand)
 

Features:
• Very Short Trigger Reset
• Custom Aluminum Fulcrum Trigger w/Polished Trigger Bar
• Skeletonized Stainless Steel Striker
• V3 Race Connector
• Titanium Safety Plunger
• Custom Springs
• Ejector Housing
• Adjustable Pre-Travel & Over-Travel
• Trigger Pull Weight Adjustable from 2-6 lbs
Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel
Convenient kits with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Gen 4 Kits available for Gen 4 models 17/19 (9mm) and 22/23 (.40 S&W) pistols. ZEV Technologies recommends this for competition use ONLY.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
bis Gen 3
 :  
410,00 € (incl. Mwst. zzgl. Versand)
 

Features:
• Very Short Trigger Reset
• Custom Aluminum Fulcrum Trigger w/Polished Trigger Bar
• Skeletonized Stainless Steel Striker
• V3 Race Connector
• Titanium Safety Plunger
• Custom Springs
• Ejector Housing
• Adjustable Pre-Travel & Over-Travel
• Trigger Pull Weight Adjustable from 2-6 lbs
Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel
Convenient kits with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Gen 4 Kits available for Gen 4 models 17/19 (9mm) and 22/23 (.40 S&W) pistols. ZEV Technologies recommends this for competition use ONLY.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
Bis Gen 3
 :  
410,00 € (incl. Mwst. zzgl. Versand)
 

Features:
• Very Short Trigger Reset
• Custom Aluminum Fulcrum Trigger w/Polished Trigger Bar
• Skeletonized Stainless Steel Striker
• V3 Race Connector
• Titanium Safety Plunger
• Custom Springs
• Ejector Housing
• Adjustable Pre-Travel & Over-Travel
• Trigger Pull Weight Adjustable from 2-6 lbs
Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel
Convenient kits with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Gen 4 Kits available for Gen 4 models 17/19 (9mm) and 22/23 (.40 S&W) pistols. ZEV Technologies recommends this for competition use ONLY.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
Für Gen 4
Restposten, Abbildung ähnlich
 :  
410,00 € (incl. Mwst. zzgl. Versand)
 

Features:
• Very Short Trigger Reset
• Custom Aluminum Fulcrum Trigger w/Polished Trigger Bar
• Skeletonized Stainless Steel Striker
• V3 Race Connector
• Titanium Safety Plunger
• Custom Springs
• Ejector Housing
• Adjustable Pre-Travel & Over-Travel
• Trigger Pull Weight Adjustable from 2-6 lbs
Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel
Convenient kits with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Gen 4 Kits available for Gen 4 models 17/19 (9mm) and 22/23 (.40 S&W) pistols. ZEV Technologies recommends this for competition use ONLY.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.

Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
Bis Gen 3
 :  
430,00 € (incl. Mwst. zzgl. Versand)
 

Features:
• Very Short Trigger Reset
• Custom Aluminum Fulcrum Trigger w/Polished Trigger Bar
• Skeletonized Stainless Steel Striker
• V3 Race Connector
• Titanium Safety Plunger
• Custom Springs
• Ejector Housing
• Adjustable Pre-Travel & Over-Travel
• Trigger Pull Weight Adjustable from 2-6 lbs
Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel
Convenient kits with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Gen 4 Kits available for Gen 4 models 17/19 (9mm) and 22/23 (.40 S&W) pistols. ZEV Technologies recommends this for competition use ONLY.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
Bis Gen 3
 :  
430,00 € (incl. Mwst. zzgl. Versand)
 

Features:
• Very Short Trigger Reset
• Custom Aluminum Fulcrum Trigger w/Polished Trigger Bar
• Skeletonized Stainless Steel Striker
• V3 Race Connector
• Titanium Safety Plunger
• Custom Springs
• Ejector Housing
• Adjustable Pre-Travel & Over-Travel
• Trigger Pull Weight Adjustable from 2-6 lbs
Precise Letoff, Fast Rest, Fully-Adjustable For Takeup & Overtravel
Convenient kits with the performance benefits of a custom trigger job to give your Glock® an ultra-smooth pull, clean letoff, and short reset without impairing the reliability of the factory safeties. Fully adjustable for pre-travel and over-travel via two easy-to-access hex-head screws (wrench included), so you can tune trigger feel to your exact requirements for maximum control. Trigger shoe and trigger safety are precision machined from 6061 T6 aluminum billet for precise engagement, smooth movement, and superb responsiveness. Engagement surfaces on the stainless steel trigger bar are mirror polished for outstanding sensitivity and consistency. Basic Fulcrum trigger includes preassembled trigger shoe, safety lever, and trigger bar. Gen 4 Kits available for Gen 4 models 17/19 (9mm) and 22/23 (.40 S&W) pistols. ZEV Technologies recommends this for competition use ONLY.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
Hier ein BEISPIEL ! geliefert wird das was oben schwarz im Text steht...
Original Glock Abzug 2,7mm Reset Weg / 5,5mm Weg gesamt / dabei 0,7mm nach dem Auslösen / Gewicht 2,1kg
Glockworx Tactical 2,5mm Reset Weg / 5,0mm Weg gesamt / dabei 0,5mm nach dem Auslösen / Gewicht 1,6kg
Glockworx Fulcrum 2,2mm Reset Weg / 4,8mm Weg gesamt / dabei 0,4mm nach dem Auslösen / Gewicht 1,5kg
Bis Gen 3
 :  
430,00 € (incl. Mwst. zzgl. Versand)
 

Tuning » Abzug 1 2 32 Artikel

Wir können natürlich auch andere Produkte der hier aufgelisteten Herstellern beschaffen!!!